How often have you seen a fridge/freezer malfunction?
This happens quite frequently, especially if you live in a cold climate.
Most fridges are equipped with a thermostat that regulates the temperature inside the fridge.
If the temperature goes above a certain level, the thermostat turns off the compressor.
When the compressor stops running, the air inside the fridge cools down and the temperature drops.
In this blog post I will explain you how to fix a common problem with refrigerators.
GE refrigerator not cooling but freezer working
This problem occurs because the compressor is not running properly. This happens usually when the refrigerant level is low. To fix this issue, you need to check if the evaporator fan is working properly. If the fan is not working, replace the evaporator coil. Also, check if the thermostat is set correctly. If these two components are not working, replace them.
1. Forget shutting the French door
If you forget to shut the French door, the cold air from outside will enter into the fridge and cool down the inside. It will take longer to get back to normal temperature. So, always remember to close the French door after using the fridge. 2. Use ice packs Answer: Ice packs help to maintain the temperature of the fridge. After opening the fridge, put an ice pack in the freezer section. Leave it there until the temperature gets back to normal.
2. Broken French door
It is very important to repair the broken French door immediately. Otherwise, the cold air from the outside will enter into the refrigerator and cool down the inside quickly. 3. Keep the fridge clean Answer: Cleaning the refrigerator is essential. Make sure to wipe off any spills and dust particles. Also, remove any items that are not needed. This will prevent the growth of bacteria and moulds.
3. Evaporator fan jam
If the evaporator fan is jammed, it will stop working. So, you need to check whether the fan is properly connected to the compressor. If yes, then try to unplug the power supply cable and plug it again. If still doesn’t work, replace the fan motor. 4. Refrigerator light switch Answer: Check if the refrigerator light switch is turned on. If it’s turned on, then turn it off. Then, turn it back on. If the problem persists, then replace the light bulb.
4. Blockage in the drain line
Check whether the drain pipe is clogged. If yes, then clear the blockage. 5. Water leak from the faucet Answer: Turn off the water supply to the sink. Remove the stopper from the faucet. Clean the faucet using soap and warm water. Replace the stopper.
5. Frosted evaporator coils
Turn off the power to the refrigerator. Open the door slightly and remove the ice tray. Check if the ice maker motor is running properly. If not, replace the ice maker motor. 6. Ice dispenser Answer: Unplug the refrigerator. Remove the ice cube trays from the freezer. Remove the ice cubes from the ice cube trays. Put the ice cubes into a bowl. Fill the ice cube trays with clean water. Reattach the ice cube trays to the freezer. Plug the refrigerator back in.
6. Damaged Air damper
Unplug the refrigerator. Remove all food from the refrigerator. Leave the doors open. Turn the compressor switch to OFF position. Wait 10 minutes. Turn the compressor switch back ON. Close the refrigerator door. 7. Refrigerator light Answer: Unplug refrigerator. Remove the light bulb from the socket. Replace the bulb.
7. Ineffective thermal resister
Check the thermostat. It may be defective. 8. Water dispenser Answer: Open the cabinet door and check if the water level is low.
8. Defective temperature control board
Check the thermostat. 9. Overheating Answer: Turn off the power switch.
9. Malfunctioning of defrost thermo regulator or thermostat
Check the thermostat. If it is not working properly, replace it. 10. Overheating 11. Improper operation of heating element
Why does the freezer work but the refrigerator is warm?
If your refrigerator is not cooling, it could mean that the thermostat is malfunctioning. To check if the thermostat is working properly, follow these steps: 1. Open the refrigerator door and remove the ice maker tray. 2. Remove the back panel from the bottom of the refrigerator. 3. Look for the black wire labeled “thermistor”. 4. Connect the red lead to the terminal marked “1” and the black lead to the terminal marked 2. 5. Replace the back panel and replace the ice maker tray. 6. Close the refrigerator door and wait about 10 minutes. 7. Check the thermometer again. If the temperature is still low, repeat step 6. 8. If the temperature is normal, the problem may be caused by a faulty circuit board. 9. If the temperature is higher than normal, the problem may lie with the compressor. 10. If the temperature is lower than normal, the problem could be due to an electrical short. 11. If the temperature remains low after following the above steps, call a professional service technician.
How do I fix my refrigerator not getting cold?
Your refrigerator is designed to cool food items while your freezer is designed to freeze food items. If your refrigerator is not cooling food items, chances are that the thermostat needs to be reset. Resetting the thermostat is easy. Simply open the door and turn the knob clockwise until the indicator lights stop flashing. Once the indicator stops flashing, press the “reset” button on the front of the refrigerator.
Why does my freezer work but the fridge doesn t?
If you notice that your freezer works but your fridge doesn’t, there could be several reasons why this happens. First thing to check is if the compressor is working properly. This is done by pressing the power button on the back of the unit. If the light turns green, the compressor is running fine. If not, replace the compressor. If the problem still persists, try cleaning the condenser coils. These are usually located near the top of the freezer door. Remove the screws holding the panel in place and remove the panel. Clean the coils using a damp cloth. After cleaning, reassemble the panel and screw it back into place.
Why is my refrigerator not cooling but the freezer is?
Yes, there is a reset button located on the back panel of the refrigerator. To reset the refrigerator, press the power button until the display explains “off” and then press and hold the reset button for 5 seconds. How to clean the ice maker in the fridge?
When you open the door of the refrigerator, the compressor turns on. This creates cool air around the coils in the refrigerator. It takes about 10 minutes for the coils to get cold enough to freeze anything. After the coils are cold, the fan circulates the cool air throughout the refrigerator.
What causes a GE refrigerator to stop cooling?
If your refrigerator stops working properly, check the power supply first. Make sure the power cord is plugged into a good outlet. Check the fuse box if the power is coming from a circuit breaker panel. If the power is still good, check the wiring connections between the electrical components and the back wall of the refrigerator. If everything checks out fine, check the thermostat. A faulty thermostat can cause the refrigerator to shut down. If the thermostat is defective, it needs to be replaced.
How do I fix my GE refrigerator that is not cooling?
GE refrigerators have a tendency to stop cooling after a period of time. This is usually caused by a problem with the compressor. It could be a bad belt, loose connection, or even a broken fan blade. To fix this issue, you will need to replace the part.