Kenmore Series 500 Washer Troubleshooting

What’s wrong with my Kenmore washer?
If you own a Kenmore washer and are having trouble figuring out what’s wrong with it, then you need to read this guide.
This guide will teach you how to troubleshoot your Kenmore washer.
1 If you own a Kenmore washing machine and are having problems with it, then this guide will tell you exactly what to look for and how to fix it.

Kenmore Series 500 Washer Troubleshooting

If you are facing any problem while using washing machine, then you can contact our customer care service team who will help you to fix the issue. We provide 24*7 services for repairing washers. Our technicians are well trained and experienced to repair any type of washer problems. For further information about Kenmore series 500 washer troubleshooting visit our website

Second Method

1 First check if the drain hose is clogged. 2 Check if the soap dispenser is working properly.

[su_youtube_advanced url = "" controls = "no" rel = "no" fs = "no" modestbranding = "yes"]

How do I put my Kenmore 500 Series in diagnostic mode?

If the washer does not turn on after pressing the Start button, check the following items: 1 Make sure the door latch is engaged.

Why is my Kenmore Series 500 washer not working?

To reset the sensor, simply remove the washer from the wall outlet, let it sit for about ten minutes, then plug it back into the wall outlet. Turn the power switch on. This will reset the sensor. How do I reset the sensor on a Maytag washing machine?

How do you calibrate a Kenmore 500 Series washer?

To reset the sensor, simply unplug the appliance from the wall outlet, wait 10 minutes, plug it back into the outlet, and turn the power switch on.

How do I reset the sensor on my Whirlpool washing machine?

If the sensor light comes on when you turn the power switch on, press and hold the Power button for about 30 seconds. This will reset the sensor. How do you clean a dishwasher?

How do you run diagnostics on a Kenmore 500 washer?

To calibrate a Kenmore washer, follow these steps: 1 Turn off the machine. 2 Remove the top panel from the front of the machine. 3 Remove the two screws holding the top panel to the machine. 4 Lift the top panel away from the machine. 5 Remove the four screws holding the back panel to the machine. 6 Pull the back panel toward you until it snaps into place. 7 Replace the top panel and tighten the screws. 8 Reinstall the machine. 9 Turn the machine on and let it run through a full cycle. 10 Check the display to see if the machine is calibrated. 11 If not, repeat steps 1-10. 12 If the machine still does not explain calibration, remove the top panel again and check the display for a code. 13 Enter the code into the machine’s user manual to correct the problem. 14 Reinstall the top panel and replace the screws. 15 Turn the machine on again and let it run through another full cycle. 16 Repeat steps 1-15 until the machine explains calibration. 17 If the machine still doesn’t explain calibration, contact an authorized Kenmore service center.

How do you reset the washing machine sensor?

To enter diagnostic mode, press and hold the power button for 10 seconds. After pressing the power button, wait 5 seconds and release the button. Press and hold the start/stop button for 10 seconds. Release the button after waiting 5 seconds. Press and hold the spin dial for 10 seconds. Release after waiting 5 seconds. Finally, press and hold the wash/dry buttons for 10 seconds. Release immediately after waiting 5 seconds.

How do you reset the sensor on a Kenmore washing machine?

Kenmore washing machines are among the most popular brands in the world. It is important to know how to run diagnostics on a kenmore washing machine. This will help you identify any problems with the machine. To check if the machine is working properly, turn it on and let it run for about 30 minutes. Then, open the door and see if the clothes are clean. If not, try again until the machine works fine. If the machine still doesn’t seem to be working properly, call a professional service technician who can diagnose the problem.