Microwave Keeps Blowing Fuse

Do you ever get stuck at home because your microwave keeps blowing fuse?
This happens to me quite often.
I don’t really understand why my microwave blows fuses.
I’m sure there’s something wrong with it but I don’t know what it could be.
In this blogpost I’ll explain you how to fix the problem.

Causes for the Microwave Keeps Blowing Fuse problem

If you are having problems with your microwave oven blowing fuse, then you should know what causes the problem. It could be any of these reasons: 1 Overheating. This happens if the heating element gets overheated. 2 Bad wiring. This happens because of faulty wiring.

Test the Magnetron

To test the magnetron, turn off the power supply switch and remove the plug from the wall socket. Then press the reset button located on top of the microwave oven. After pressing the reset button, wait for about 30 seconds. If the light turns green, the magnetron is working fine. If not, replace the magnetron.

Problem with the cooling fan

If the cooling fan does not run properly, the problem could be caused by the following reasons: 1 The fan motor is damaged. 2 The fan belt is broken.

How to make it effective?

Step 1: Check if the fan motor is working correctly. Step 2: Check if the fan belt is broken. If yes, replace the fan belt. Step 3: Clean the dust from the fan blades. Step 4: Replace the fan motor.

Issue of a loose screwdriver

A loose screwdriver is not only dangerous but also annoying. It is very easy to lose a screwdriver while doing any task. A loose screwdriver can easily fall off the table and get lost. So, always carry a spare set of screwdrivers with you. How to prevent losing a screwdriver?

How to fix it?

1 Keep a spare set of screwdriver in your car. 2 Carry a spare set of screw driver in your pocket.

How to remove it?

High voltage capacitors are used in many electrical devices such as power supplies, radios, televisions, computers, and other appliances. These capacitors are usually found in the back of these devices. To remove a high voltage capacitor from a device, follow these steps: 1 Turn off the power supply circuit breaker. 2 Remove the screws holding the unit together. 3 Disconnect the wires attached to the terminals. 4 Pull the unit apart. 5 Unplug the unit. 6 Clean the area around the unit with rubbing alcohol. 7 Replace the screws and reattach the unit. 8 Reinstall the power supply circuit breaker and turn on the power supply. 9 Check the connections between the unit and the power supply. 10 Test the unit to ensure it works properly. 11 Use caution when handling the unit. 12 Store the unit safely after use.

Door interlock

A door interlock is a safety feature that prevents unauthorized access to a building or room. It is designed to prevent people from entering a locked room or building if someone else is already inside. A door interlock system consists of two parts: a lock and a sensor. The lock is installed on the outside of the door. The sensor is installed on the inside of the door. When the door is closed, the sensor detects the presence of the lock. This triggers the alarm system to sound an audible warning signal. The alarm system also sends a message to the central monitoring station.

Test the door interlock of the microwave

To test the door interlock of your microwave, follow these steps: 1 Turn off the power switch. 2 Open the door of the microwave. 3 Close the door. 4 Press the button marked "test". 5 Wait for 10 seconds. 6 Check whether the light flashes red. 7 If yes, press the button again. 8 Repeat step 6 until the light turns green. 9 Test the other doors.

How to replace it?

To replace the door interlock of a microwave oven, you need to remove the back panel of the microwave. Then, you need to remove screws from the bottom plate. After that, you need to remove two screws from the top plate. Finally, you need to remove three screws from the front panel. References

Repair your oven or replace it?

How To Replace A Microwave Door Interlock Zjg_mDq0XBQ